Finding a transmitter you cannot see
In amateur radio direction finding (ARDF, also called fox hunting or radio orienteering) small transmitters are hidden in a forest and runners find them with a map and a receiver that has a directional antenna. Every beginner asks the same question: how does a tone that gets louder and quieter lead you to one spot among the trees? Here you stand at the start, turn the antenna, read the meter, draw a bearing on the map, move to another place and draw a second one. Where the lines cross is where you run.
The map is generated from the number in the address, so a link opens the same forest and the same hidden transmitters for anyone. Learning mode has one transmitter that sends all the time and explains what the meter is telling you. Classic and Sprint follow the timing of the international rules.
Experiments to try
- In Learning on 3.5 MHz, stand still at the start and turn the antenna 5° either side of the loudest direction, then 5° either side of the null. At the maximum the meter peaks at the same value (the loop loses less than 0.1 dB there), five degrees from the null it peaks about 20 dB lower, and in the null the tone sinks into the noise: the meter shows 2 to 5 dB, although the pattern itself is 34 dB down.
- Take three bearings from places a few hundred metres apart and watch the shaded tolerance area shrink when the lines cross at a wide angle.
- Walk close to the transmitter without attenuation. The needle sits at the top in almost every direction and the null becomes a sliver a few degrees wide. Press Att + until the needle drops and the null opens up again.
- On 144 MHz with reflections on, take a bearing from behind a hill. After you find the transmitter, the Bearings panel shows how far off that bearing was.
- In Classic, stay at the start for one five-minute cycle and take a bearing on every transmitter before you set off, then plan the order.
What to observe
- The maximum of every antenna is broad and the null is sharp, so the 3.5 MHz loop is aimed with its null, and the 144 MHz beam, aimed at its maximum, gives less certain bearings.
- The level falls by 6 dB for each doubling of distance on 3.5 MHz and by 9 dB on 144 MHz, where forest and hills take more on top of that.
- The attenuator setting tells you the distance. With no attenuation the needle reaches the top about 400 m from a 3.5 MHz transmitter, and each 10 dB step moves that point about three times closer.
- Behind a hill on 144 MHz the signal can come from a slope that reflects it. The bearing then points at the slope, and the level flickers as you walk because the direct and the reflected wave add and cancel.
The two receivers
3.5 MHz: loop and sense antenna
The loop (in real receivers a coil on a ferrite rod) has a figure-eight pattern: loudest when the arrow points at the transmitter or directly away, silent when the transmitter is at right angles to the arrow, perpendicular to the plane of the loop. The dashed line through your position is this null line. With Sense on, the signal of a short vertical antenna is added to the loop's and the pattern becomes a cardioid, loudest ahead and silent behind, which tells front from back. On a real receiver it is a spring button; here Space works that way and the Sense button switches it on and off.
So: with Sense on, turn to the loudest tone to learn the side, then switch it off and turn until the tone disappears for the precise line. Null line draws that whole line; Mark draws a bearing along the arrow.
144 MHz: three-element beam
A reflector, a driven element and a director give one maximum ahead, 62° wide between the points 3 dB down, with the back about 20 dB weaker. There is no front and back confusion, but the broad maximum is less precise than a null. This is the antenna Hidetsugu Yagi described in English in 1928 from work with Shintaro Uda.
How the races are simulated
- Classic: five transmitters on one frequency send their call signs for one minute each in a five-minute cycle from 0:00: MOE (1), MOI (2), MOS (3), MOH (4) and MO5 (5), at 12 words per minute. The finish beacon sends MO continuously on another frequency. Transmitters are at least 400 m apart and at least 750 m from the start. You may skip some; the run ends at the finish beacon and counts the number found first, then the time.
- Sprint: one loop of the sprint format on 3.5 MHz on a smaller map, 12 seconds per transmitter in a one-minute cycle at 10 words per minute.
- Learning: one transmitter sending MOE without a break, 600 to 1100 m from the start, with tips under the map.
- Time speed multiplies the race clock and your running speed (by default 4× in Learning, 2× in Classic, so each transmitter is on the air for 30 seconds of real time, and 1× in Sprint, 12 seconds as in a real sprint); the Morse keeps its real speed so you can count the dots after MO.
- A flag appears within about 25 m in the forest or 50 m in the open, and you register it by walking within 6 m. Paths, open land, three kinds of forest and the slope set your speed.
The model
The level L is given in decibels above the noise of the receiver, at the maximum of the antenna, with d the distance in metres:
144 MHz: L = 122 − 30 log10 d − Aforest − J(v)
On 3.5 MHz the wavelength is 84 m and the page treats hills and trees as transparent. On 144 MHz (2.07 m) the exponent lies between free space (20) and flat ground (40). The forest adds A = 12 (1 − e−0.05 dF/12) dB for dF metres of forest on the line, at most 12 dB. The highest point of terrain above the line from the transmitter antenna (2.5 m above the ground) to yours (1.5 m) is treated as a knife edge of height h:
The antenna patterns, with θ the angle between the arrow and the direction the wave comes from:
loop with sense: g = (1 + cos θ) / 2
beam: g ∝ |f(θ) Σ Ik ej 2π xk cos θ / λ|, f(θ) = cos((π/2) sin θ) / cos θ
The beam's elements sit at x = −0.2λ, 0 and 0.15λ with currents 0.7∠126°, 1 and 0.5∠−160°. With reflections on, up to eight of the steepest slopes reflect the 144 MHz wave with an amplitude of 0.6 f (d/L)1.5 and a phase of 2π(L − d)/λ, where L is the length of the reflected path and f says how squarely the slope faces both you and the transmitter. Each wave is weighted by the antenna pattern in its own direction and the waves are added with their phases.
The receiver subtracts the attenuator (0 to 90 dB in 10 dB steps), and the meter shows the result from 0 to 40 dB. Above 40 dB the receiver saturates: the output is limited to −10 log10(10−L/10 + 10−4), so a strong signal reads the same in most directions. The tone is 800 Hz on 3.5 MHz (a keyed carrier heard through a beat oscillator) and 1000 Hz on 144 MHz (a keyed tone).
The crossing and its tolerance
The cross mark is the point with the smallest sum of squared distances to your lines for that transmitter, each weighted by 1/s2 with s = d tan σ, where d is the distance from where you took the bearing. The shaded ellipse is where the transmitter lies with 95 % probability if each bearing has a random error with a standard deviation σ of 3° on 3.5 MHz or 8° on 144 MHz: its half-axes are 2.45 times the square roots of the eigenvalues of (Σ n nT/s2)−1, with n the unit normal of each line. The tolerance grows with distance and when the lines cross at a narrow angle, and it says nothing about a bearing that points at a reflection.
Limits of the model
- The terrain is generated, not surveyed, and the levels are chosen to behave plausibly rather than measured in a real forest.
- On 3.5 MHz there is no near field, no shielding by your body and no effect of terrain; on 144 MHz only a few slopes reflect, trees and buildings do not.
- The headings are exact. A real competitor reads a compass while running and draws the lines by hand.
- Sprint has one loop only, without the fast loop and the spectator control, and there is no finish corridor.
Controls
- Mouse: move the pointer over the map to turn the antenna, click to draw a bearing along the arrow (Shift+click draws the null line), hold the button to walk towards the pointer, and turn the wheel to zoom while a run is on.
- Touch: tap the map to point the antenna at that spot, touch and hold to walk towards your finger, then use Mark or Null line. The 1° buttons repeat while you hold them.
- Keyboard (with the map focused): arrow keys or WASD walk, Q and E turn the antenna by 1° (with Shift by 10°), hold Space for Sense, B draws a bearing, N draws the null line, Backspace removes the last line, minus and plus change the attenuator, Z zooms, C switches to the finish beacon and back, F is full screen, P or Esc pauses and Enter starts. On a question over the map, Esc keeps searching.
- Buttons: Start and Pause, the 1° turns, Sense (on and off), Mark, Null line, Undo and the attenuator under the map; zoom and full screen at the right edge of the map; map number, new map, link, time speed, reflections and Show the transmitters in the Course panel. Show the transmitters ends the run, so it asks first.
- Sliders: antenna direction in the Receiver panel and the volume.
Sources
- IARU Region 1, ARDF Rules, Part B (2025): transmitter codes and timing, distances, sprint rules and transmitter specifications.
- ITU-R, Recommendation P.526, Propagation by diffraction: the single knife-edge loss J(v).
- H. Yagi, Beam transmission of ultra short waves, Proceedings of the IRE 16 (1928), 715–740.